[ fanfon @ 13.06.2016. 19:59 ] @
| Hteo bih nekom odneti da mi napravi ovo sa snimka. Ima li neko ko bi mogao da prevede sa engleskog tacne nazive ovih "sastojaka" da bih mogao da ih nabavim: https://www.youtube.com/watch?...j-Njs9nSiwFTETj2D&index=23 PURCHASE LIST: (paint section) 4 - Five gallon buckets (bldg materials) 1 - roll 1/2 inch mesh that is 24" wide (need 40 inches in length minimum) 1 - roll 1/4 inch mesh that is 24" wide (if using additional screen sizes) 1 - roll 1/8 inch mesh that is 24" wide (if using additional screen sizes) (plumbing) 10 - 1 inch PVC 90 degree elbows 9 - 1 inch PVC Tee fittings 5 - 1 inch PVC end caps 4 - 1 inch PVC pipe 10 foot lengths 2 - 1 inch PVC 45 degree fittings 1 - 1 inch PVC cross fitting (4-way cross) 1 - 1 inch PVC coupling 1 - 1 1/4 inch PVC pipe 5 foot length 1 - bottle PVC Primer (clear looks neater) 1 - bottle PVC Cement (hardware) 8 - #8-32 x 1/2 inch machine screws w/nuts 8 - #8 fender washers 15 - #10-24 x 2 inch machine screws w/nuts (option - 4 of these are used for legs) 5 - #10-24 wing nuts (option - 4 are used for legs and 1 is used for axle) 6 - #10 fender washers 1 - 1/4-20 all thread (need 26 inches minimum) 12 - 1/4-20 lock nuts 8 - 1/4 inch washers 2 - 48 inch bungee cords (optional - needed if using additional screen sizes) 2 - small caribeener for bungee cords (optional - needed if using additional screen sizes) (electrical) 1 - bag 8 inch black UV stabilized wire ties (zip ties - need 10-15 ties total) (tools) 1 - 1 3/8 inch hole saw with arbor CUT LIST: --1 INCH PVC PIPE-- 2 @ 13 1/2 inches (cross leg supports) 10 @ 6 inches (handle and chassis corners) 1 @ 41 1/2 inches (axle) 2 @ 29 inches (chassis sides) 12 @ 3 inches (leg feet and chassis leg slip nipples) 2 @ 21 inches (infeed legs) 2 @ 24 1/2 inches (outfeed legs) 2 @ 2 inches (outfeed leg 45 degree nipples 1 @ 7 inch (portion of handle that gets screwed to axle coupling) --1 1/4 INCH PVC PIPE-- 4 @ 6 inches (Legs slip attachment fittings) 1 @ 3 7/8 inches (handle spinner) --BUCKETS-- 2 @ 7 inches from top rim 2 @ remove bottoms and cut lengthwise --SCREENS-- 1 @ 40 inches long for each size mesh PARTS BY COMPONENT: --INFEED LEG-- 4 - 1 inch PVC @ 3 inches (feet) 2 - 1 inch PVC @ 21 inches (legs) 1 - 1 inch PVC @ 13 1/2 inches (cross leg support) 2 - 1 inch PVC end caps 2 - 1 inch PVC 90 degree elbows 2 - 1 inch PVC Tee fittings 2 - #10-24 2 inch machine screws w/nuts 4 - #10 machine screw washers --OUTFEED LEG-- 4 - 1 inch PVC @ 3 inches (feet) 2 - 1 inch PVC @ 24 1/2 inches (legs) 1 - 1 inch PVC @ 13 1/2 inches (cross leg support) 2 - 1 inch PVC end caps 2 - 1 inch PVC 90 degree elbows 2 - 1 inch PVC Tee fittings 2 - #10-24 2 inch machine screws w/nuts 4 - #10 machine screw washers --CHASSIS-- 8 - 1 inch PVC @ 6 inches (corners) 4 - 1 inch PVC @ 3 inches (nipples between 45 degree and 1 1/4 inch leg slip) 4 - 1 1/4 inch PVC @ 6 inches (leg slips) 2 - 1 inch PVC @ 2 inches (nipples between chassis leg Tee and 45 degree) 2 - 1 inch PVC @ 29 inches (sides) 4 - 1 inch PVC 90 degree elbows 4 - 1 inch PVC Tee fittings 2 - 1 inch PVC 45 degree elbows 1 - 1 inch PVC Tee fitting drilled for axle 1 - 1 inch PVC Cross fitting drilled for axle 11 - #10-24 2 inch machine screws w/nuts 16 - #10 machine screws washers 6 - #10 fender washers 1 - bag of 8 inch black UV stabilized wire ties (zip ties) --HANDLE, AXLE, & SCREEN-- 2 - 1 inch PVC @ 6 inches (handle) 1 - 1 inch PVC @ 41 1/2 inches (axle) 1 - 1 inch PVC @ 7 inches (length that connect handle to axle coupling) 1 - 1 1/4 inch PVC @ 3 7/8 inches (handle spinner) 1 - 1 inch PVC end cap 2 - 1 inch PVC 90 degree elbows 1 - 1 inch PVC coupling 2 - #10-24 2 inch machine screws w/nuts 4 - #10 machine screw washers 8 - #8-32 x 1/2 inch machine screws w/nuts 8 - #8 fender washers 1 - 1/4-20 all thread (need 26 inches min) 12 - 1/4-20 lock nuts 8 - 1/4 inch washers 2 - 48 inch bungee cords (if using additional screen sizes) 2 - small caribiner for bungee cords (if using additional screen sizes) 1 - 1/2 inch mesh 24 inches wide @ 40 inches long (for each size mesh) TOOLS USED: - miter saw (or pvc cutter) - hack saw with metal cutting blade (could use jigsaw as well) - tin snips or heavy duty scissors - wire cutters - tape measure - 1 3/8 inch hole saw with arbor - 3/8 inch drill - 1/4 inch drill bit for all hardware except all thread - 5/16 inch drill bit for 1/4 inch all thread pilot holes - phillips screwdriver - 7/16 inch wrench - 3/8 inch wrench - 7/16 inch socket and ratchet - needlenose pliers - vise grips (used while putting lock nuts on) - tape - dremel - sandpaper |
.